Aerospace Science Engineering Facilities

Experimental Aerodynamics Laboratory

The experimental aerodynamic facilities consist of two wind tunnels, two free surface water channels and a flow-visualization smoke tunnel.

(a) Wind Tunnels
The Department operates a low speed closed circuit wind tunnel facility with a 2' x 3' test section. The test section is equipped with a 6 component pyramidal balance. A computer-controlled 16-port solid- state pressure data acquisition is also available. This equipment is used for the aerodynamics laboratory class as well as for faculty and undergraduate research and design projects. An open circuit 9n x 9n low speed open circuit wind tunnel is also available.

The 2ft x 3ft Low Speed Close Circuit Wind Tunnel

The Department also has a smoke flow visualization tunnel with several experiments including flapped wing, rotating cylinders etc.

Flow Visualization Smoke Tunnel

(b) Water Tunnels

A free surface water channel is with a 15in x 20in test section is available in the Department. This facility has optical access from the sides, bottom and a down stream window. The water channel has a pressurized four-port dye injection system for flow visualization. The water channel is used for instruction as well as research.

15in x 20in Water Tunnel

The Department also has a table-top version of the free surface water channel with a test section of 7in x 10in. This water channel that is used primarily for instructional purposes, has a sting balance as well as a dye injection system for flow visualization. Several experiments such a cylinder, delta wing etc. are available.
Table Top Water Tunnel                                   Typical Flow Visualization Experiment

(c) Volumetric Particle Image Velocimetry

A state of the art volumetric PIV system is available for non-intrusive flow diagnostics. The system has interrogation volume of 140mm x 140mm x 100mm. The system uses two 200 mJ Nd-Yag pulsed lasers and a three 4MP cameras. The system has a spatial resolution of 3mm3.

Volumetric PIV System Camera Mount Typical Data

Propulsion Laboratory

The propulsion facility consists of a fully instrumented jet engine. The engine is computer-controlled data acquisition system. The students can perform several experiments using this facility.


Automatic Flight Controls Laboratory

Several experiments are available to students to strengthen their concepts of automatic controls and application to flight controls. These include:

Mass-Spring-Damper System
This system provides an understanding of rigid body PID control
, , lead/lag compensators, phase and gain margin, trajectory tracking, and regulation. Students also conduct experiments using high order collocated and non-collocated system control. Mode shapes, natural frequencies, transient and frequency responses are also studied.

(b) Hardware in the Loop (HITL) Facility

An HITL setup is used to teach concepts of automatic flight control. This setup consists of an arduino-based autopilot that is linked to the Matlab aerospace toolbox. An open-source  mission planner and X-plane is used for the simulation environment. Students implement the control algorithms on low cost UAVs.

Structures Laboratory

The structures laboratory provides hands-on activities for material testing, composite materials layup (including vacuum bagging) and measuring stresses using strain-gauged simple cross sections as well as built-up structures.

Flight Vehicle Design Laboratory

The laboratory has an array of computers running Windows for student course and project work, as well as for faculty research and curriculum development. Some of the computers were acquired by donations from alumni. The laboratory also has a large out-of-window flight simulation environment based on Micorsoft Flight simulator that is used for research as well as teaching aircraft performance, and stability and control. The various software packages available are Unigraphics NX, NASTRAN, Multifoil, Star CCM+, Matlab with Simulink and Aerospace Tool Box. 

The Department also has a 6-node (4-processor/node) cluster computer that is used by students to learn computational fluid dynamics and structural mechanics in a parallel computational environment.

Satellite Laboratory

The Department is aggressively pursuing the development of a cube-sat program.  Students use a nanosat simulator gain hands-on experience on various systems such as systems, structural, electrical & thermal engineering, attitude determination & control in a simulated microgravity environment. Students also learn satellite communication, command & data handling, and systems integration.

Model Fabrication Laboratory

This laboratory is used to build models for the wind tunnel, and is used as a shop for various student design projects, such as a radio-controlled airplane, a model for aircraft fuel tank and gauge, and an inverted V-tail for an aircraft design. The department is presently proposing to expand the capabilities of this laboratory to include structural testing of models.